We design our panels keeping in mind the experience gained from installation contracts resulting in increased safety of personnel and equipment, ease of maintenance, installation and commissioning. The design incorporates a host of safety and convenience features. We meet the requirement of international standards along with compliance to local standards and regulations. We have type testes our Power panels for short circuit withstand capacity of 50kA RMS 1 second. Power control Centre, in which your main incomer is directly connected to your LT transformer either by bus duct or cable & all protection given to this incomer i.e. overcurrent & earth fault relay, restricted earth fault relay. Also this panels have DG incomer as per client requirement of continues power supply even if main supply will be OFF. PCC Panel also includes outgoing feeders like PDB, MLDB and APFC & MCC feeders' incomer.

SALIENT FEATURES - SWITCH BOARDS:-

Designed to meet the requirement of IS-8623 on Factory build assemblies

Busbar rating upto 4000A

Short circuit withstand capacity of 50kA for 1 sec RMS

Totally enclosed, Cubicte type compartmentalized construction

Free standing, Floor mounting

Extendable on both sides

Cable entry from Top & Bottom

Customer choice of switchgear

DMC/SMC reinforced FRP material for bus bars support.

Front and Rear access

Single / Double Busbar system

Auto source changeover

PLC logic for Source changeover

Distribution Panels suitable for installations

Metal treatment with seven tank process followed by electrostatic power coating.

Technical Data:

Rated insulation : 1000 volts, 50 Hz..

Rated Operational Voltage : Power circuit-440 Volts AC, 3Phase 4wire or 3 wire. Control circuit-110 Volts, 220 Volts, 415 Volts AC or 220 Volts, 110 Volts DC.

Ambient Temperature : 40 c

Degree of protection : IP protection: IP 42 to IP 65

Minimum Busbar clearance : Phase to Phase 25 Phase to Neutral 25mm..

Automatic Power Factor Control Panels are mainly used for the improvement of Power Factors. Power Factor can be explained as ratio of active power to apparent power and it is a key factor in measuring electrical consumption. Everyone knows that how costly electricity has become in present time. Therefore it becomes utmost important to cut down on electrical consumption for reducing expenditure.

APFC Panels come real handy in the achievement of this purpose. Use of these control panels become in-dispensable in those industries where electrical installations are meant to supply to large electrical load. A dip in Power Factor can attract operational losses and a penalty from electricity board, responsible for electricity supply. MNR Electricals offer vide range of standard and customized APFC panels and are competitive in the Industry. APFC Panels are effectively and automatically manage quickly changing and scattered loads along with the retention of high Power Factor. We are renowned manufactures of APFC Panels symbolized with quality and reliability. These are available in different current ratings to cater to distinct application.

Automatic Power Factor Control Panels are mainly used for the improvement of Power Factors. Power Factor can be explained as ratio of active power to apparent power and it is a key factor in measuring electrical consumption. Everyone knows that how costly electricity has become in present time. Therefore it becomes utmost important to cut down on electrical consumption for reducing expenditure.

APFC Panels come real handy in the achievement of this purpose. Use of these control panels become in-dispensable in those industries where electrical installations are meant to supply to large electrical load. A dip in Power Factor can attract operational losses and a penalty from electricity board, responsible for electricity supply. We offer vide range of standard and customized APFC panels and are competitive in the Industry. APFC Panels are effectively and automatically manage quickly changing and scattered loads along with the retention of high Power Factor. We are top manufacturer, dealer and supplier of APFC Panels Hyderabad, Delhi, Mumbai, Bangalore and symbolized with quality and reliability. These are available in different current ratings to cater to distinct application

SALIENT FEATURES:-

Maintains high Power Factor constantly

High efficiency

In-built independent fuses

Prevents leading Power Factor in low load conditions

Clearly marked buttons and indicators

Minimizes harmonic current

Easy Maintenance and easy to removable capacitor.

Corrosion-resistant

Electrical insulation

Protects electrical equipments

Microprocessor based relay for controlling power factor within required values.

RTPFC Panels using Thyristor based capacitor switching.

Fully ventilation type panel.

Use of capacitor duty contractors.

Always maintain 0.99PF.

High-speed power factor correction.

Provision of detuned reactors the panels for reliable operation in presence of harmonics.

We manufacture and supply a comprehensive spectrum of matchless Automatic Mains Failure Panels. Our electrical AMF Panels are durable and meet customer's exact requirement. Our experts customize the product range in accordance with client's specific requirements. These Customized AMF Panels can be availed in various sizes that best fit to customer's requirement.

AMF Panels or Automatic Mains Failure Panels are the important part of an industry which will automatically switch to the power backup or generators when there is a power loss. Without AMF Panels we must start the generators manually, and may cause data loss or work loss. MNR Electricals are the top manufacturers, dealers and suppliers of AMF Panels in Hyderabad, Mumbai, Delhi, Bengaluru.

SALIENT FEATURES:

Generator starting, stopping and monitoring sequence

Automatic shutdown during any DG fault.

Configurable via front panel feather touch push buttons.

Configurable Solid state Outputs.

Large number of configurable timers.

Continuous monitoring of three-phase voltage/current/frequency of mains and DG along with battery voltage of DG

Gratings

An open grid assembly of metal bars, in which the bearing bars, running in one direction, are spaced by rigid attachment to cross bars running perpendicular to them or by bent connection bars extending between them.

Bearing Bars:-

Load carrying bar made from steel strip, or slit sheet or from rolled or extruded aluminium and extending in the direction of the grating span.

Cross Bars:-

The connecting bars, made from steel strip, slit sheet or rolled bars, or from rolled or extruded aluminium, which extend across the bearing bars, usually perpendicular to them. They may be bent into a corrugated or sinuous pattern, where they interact the bearing bars which are welded to them.

The Auto Transformer Panel or reduced-voltage starter places the motor on the secondary of the auto transformer while starting. The ATS Panel is best suited when there is a requirement in reduced current and a high torque with longer acceleration for motors like blowers, pumps, extruders, compressors, crushers. We are the best and top manufacturers of ATS Panels or Auto Transformer Panels in Mumbai, Delhi, Bengaluru and Hyderabad with the best experience in the domain of producing Electrical control panels with highest industry standards and quality.

SALIENT FEATURES:

HIGHLY Rated Transformers and contractor.

The entire motor protection/safety device included.

Double door/cubical type duly expoxy powder coated.

Used for Heavy HP/Rating Motors.

Our clients can avail from us a broad array of Relay Panels in different designs and technical specifications in order to, meet their diverse industrial requirements. These panels are designed by our professionals as per the set industry norms using high-quality raw material and advanced technology. Further, these panels are carefully tested on different industrial parameters in order to ensure their high performance and longer service life. These high-quality relay panels are available with us in different specifications at a cost-effective price range.

Fully automatic synchronizing panels operated by microprocessor-based relays.

AMF, Auto synchronizing, Manual synchronizing, Auto load sharing, Active & Reactive power management with protection such as U/V, O/V E/F, O/C IDMT, Reverse power etc.

Load balance metering such as Ammeter, Voltmeter, KW, PF, KWH, Double.

Volt, Double Frequency Meter & Synchroscope etc. COLD FORM LAMINATE (Alu-Alu Blister) is been represented as the new generation in pharmaceutical packaging, Material with - Best barrier performance at present which is Suitable for High-speed packing applications, Barrier to – UV rays, Moisture & Gases.

SALIENT FEATURES:

Load Manager, Power reverse protection Earth fault, filed lost control, auto manual synchronization, dual volt meter, dual frequency meter, all comes in a single panels.

Automatic start and stop of the generator and changeover the EB/generator lines

Auto/manual selector is available

Genset stop with delay of 3 min

Hooter-alaram annunciation for fail to start

Checklist to find the fault and to correct

4ST switch control for healthy start and stop of genset

Manual start & stop switch

Available with emergency stop switch

Auto LLOP (Low Lube Oil Pressure) and (High Water Temperature) protections are available (LLOT & HWT Sensors-Relays are not part of this panel\provided with control wires and safety according to their generators standard

We provide PLC Control Panel. Our control panels are capable of giving higher output and consume less power. Compact in design, these drives and PLC Control Panels are largely used in the global arena.

SALIENT FEATURES-SWITCH BOARDS:-

Very stable, industry-tested PLC processor

Solid, tested ladder logic (built to be a PLC first)

Excellent ladder logic programming software

Internal DC power supply

Easily configured for the project

Expandable for any size remediation project

Large memory for basic data logging requirements

Mod bus communication protocol can be used

Auto-tuning PID loops

Built-in clock/calendar for data logging and alarm data stamping

Two communication ports, which allows off-site modem plus on-site display or touch screen

Ethernet module available

Expansion or replacement modules almost always available for next day delivery anywhere in North America

Our PLC control systems can be used for stand-alone system control, remote system control, monitoring, reporting, and data logging.

Distribution boards normally comprise of either ACB/MCCB as the incomer and the MCCB/SFU/MCB as the outgoing feeders. The distribution Boards are a free-standing type or the wall mounting type. Distribution boards can be offered in compartmentalized or not compartmentalized design with single or double door configuration. Distribution boards have the adequate space for the cable termination. Terminals are shrouded for the safety.

SALIENT FEATURES- DISTRIBUTION BOARDS:

Designed to meet the requirement of IS-8623 on Factory built assemblies.

Flexible construction allows the positioning of the bus bar at the top or bottom.

Bus bars and vertical risers tested for 50KA for a sec.

DMC/SMC reinforced FRP material for bus bars supports.

Our clients can avail from us a wide range of Feeder Pillars. Our offered range of pillars are manufactured using optimum grade raw material like steel and many other components that are procured from certified and authentic vendors, who are well known in the market. Further, these products are manufactured in compliance with the set industry norms and standards. In addition to this, these products are tested on various characteristics, before delivering it to our customers. These products are known for easy installation & easy maintenance.

Bus duct with a required rating, Fault level.

Designing of Bus Duct to achieve required Fault Level, considering temp. Rise, Thermal Rating, Stress, withstand capacity and all applicable dating factors.

Bus Duct up to 4000A with Copper/Aluminium Busbar

Bus bar supported by DMC/SMC Support

Bus bar with Heat Shrinkable Sleeve.

Indoor/Outdoor Duty, the Separate adapter at both ends with Space heater & earth bus.

Air insulated, Non-segregated type.

Short circuit rating of 50KA for 1sec RMS

Also non-magnetic aluminium enclosures

Flexible terminations

Flexible In-line Connections

RISING MAINS

Air insulated, Non-segregated type.

Indoor Vertical Erection type

The bus bar of up to 1250A ratings

Short circuit rating of 50KA for 1sec RMS

Fixed type Tap off boxes

Flexible In-line Connections

Fire barriers

Wall Supports

Swaged Poles

MNR is a recognized, top-of the line Black pipe manufacturer, which ensures best quality raw materials for pole manufacturing, in house. MNR poles are available in galvanized and painted forms in all lengths, satisfying customer’s requiremen.ts. MNR Brand of poles therefore enjoy a leadership position in the market place, and are trusted widely for product quality, infrastructural capability, technology process eligibity and resourcefulness..

Designed/Customized Poles

To meet the challenges of architects, planners & end-users; we design our poles and the brackets with plate and square/circular pipes. We have developed various aesthetically designed steel poles to suit all the purposes.

Apart from the designs in this catalogue you are welcome to send in your designs for customization to meet your specific need.

Materials : Mild Steel, Aluminium, Stainless Steel

Finish: Hot dip galvanized, Self-color, Red oxide, Enamel painted.

Length: Standard length of a tray is 2500mm

Steel: As per IS: 2062 / 1079

Galvanizing: As per IS: 2629 / 4759

Ladder Type Cable Trays

Ventilated Trough Type Cable Trays

Straight Splice Plates

90-degree Horizontal Bends

45-degree Horizontal Bends

Horizontal Tees

Horizontal Cross

90 degree Vertical outside Bends

45 degree Vertical outside Bends

30-degree Vertical inside Bends

Vertical Bend Segment (VBS) Vertical Tee Down

Left, Right Hand Reducer.

Frame Type Box Connector

Barrier Strip Straight Section

Ventilated Channel Straight Section

Channel Cable Tray, 90-degree Vertical Outside Bends

Chain link sizes available:

12 gauge or 2.5mm: 1.25”, 1.5”, 2.5”.

10 gauge or 3mm: 2”, 2.5”, 3”, 3.5”, 4”

8 gauge or 4mm: 2”, 2.5”, 3”, 3.5”, 4”

Chain link wires available:

Galvanized and PVC coated.

Posts available:

Angle and pole.

Our products and services:

Chain link

Fencing posts

Turnkey projects

An open grid assembly of metal bars, in which the bearing bars, running in one direction, are spaced by rigid attachment to cross bars running perpendicular to them or by bent connection bars extending between them.

Bearing Bars:-

Load carrying bar made from steel strip, or slit sheet or from rolled or extruded aluminium and extending in the direction of the grating span.

Cross Bars:-

The connecting bars, made from steel strip, slit sheet or rolled bars, or from rolled or extruded aluminium, which extend across the bearing bars, usually perpendicular to them. They may be bent into a corrugated or sinuous pattern, where they interact the bearing bars which are welded to them.

Solar Module Mounting Systems

We are one of the largest manufacturer of solar module mounting system in India. We offer a wide range of mounting solutions for all types of solar projects. Our in-house production, quality control and continual product development guarantees excellence of our entire product range.

Mounting Structures – Types of Sections:

C-CHANNEL

C-CHANNEL with Lip

Struct Rail

Z Channel

Z Channel with Lip

Sigma Section

L Angle

Hat Section

Hot Rolled Section

Main Products

Ground based module mounting structures

Roof mounted structures

Module mounting clamps

Concentrated solar power support structure

Pre fabricated inverter rooms and control rooms

Solar powered telecom towers

Motor Control Center (MCC) Panels

Power Control Center Panels (PCC)

Automatic Power Factor Control Panels

AC/DC Drive Panels (VFD, SOFT Satarter)

LT Distribution Panel Boards

MCB Distribution Boards

Fuse Distribution Boards

A.M.F (Auto Mains Failure) Panels

DG Auto/Manual Load Sharing Panels

Control & Relay Panels, Control Desks

Auto Transformer Stater Panels (ATS)

Medium Voltage Segregated Bus Ducts

Non Segregated Bus Ducts

High Voltage 11/33kv Bus Ducts

Panels Erection & Commissioning

GI, MS Cable Trays, Cable Ducts (All Sizes and Types)

Outdoor LT Kiosks

Change Over Panel Boards

D.G. Set Control Panels

Lighting Control Panels

Bus Coupler Panels

Synchronizing Panels

Metering Panel Boards

Junction Boxes, Feeder Pillars

Residential Distribution Boxes

LPC Panels

GI, Aluminium, Copper Flat and Wire

G.I. Strips & Plates

These are used as earthing material along the length of cable trays & electrodes.

These strips are available in different widths and thickness confirming to I.S.2062; 1992

Aluminium Strips

These are used for binding the cable Trays

GI Wire

These are used for binding the Cable Trays and available in various Gauges.

Stainless steel (SS) Bolts & Nuts & Washers Earthing Rods in M.S. Galvanized up to 40mm Dia ISMC CHANNEL & Angles.

Any other size of your choice can be supplied on order. Note: Hot Dip Galvanized after fabrication I.S. 3043: 1987

Earthelctrodes & Compound

Advanced Earthing Electrodes

MNR advances earthing electrodes are engineered to endure the most enviously corrosive environments. These electrodes are robust enough to withstand fault currents of very high magnitude. Fabricated from excellent quality G.I./Copper pipes, these electrodes are virtually indestructible.

The pipes are profiled with proprietor super conductive crystal-line compound/ which encloses the primary conductor completely, increasing its surface are and also forming a protective layer against corrosion. It never allows the primary conductor to come in direct contact with corrosive elements in the surrounding soil.

Features:

Robust design to last for a lifetime

Three level protection from corrosion OUTER Pipe (GI/Copper

Layer of super conductive crystalline compound

Primary conductor (Pipe/Strip)

We bring forth an impeccable array of Perforated Cable Tray for our clients. Offered trays are widely used for installation of regular cables as well as controlled cables in various industries and sectors. Our range is widely acclaimed for its ability to accommodate a large number of branch lines giving a high load bearing capacity. Furthermore, we also offer these cable trays in various customized specifications as per the requirement of our clients.

Ladder Type

Backed by an innovative setup, we bring forth a wide collection of Ladder Cable Tray to our valued clients. Our offered range of tray is widely acknowledged for its corrosion resistance that helps in efficient transmits of the product. These trays are designed and developed by making use of qualitative raw material that are sourced from the most renowned vendors of the industry. Customers can avail these in various sizes and grades as per their detailed specifications.

Angular Ladder Type(ALTCT)

MNR Angular Ladder Type (ALTCT) are fabricated to M.S. Angles Confirming to I.S. 2062:1992.

M.S. Angles are used as Runners and M.S. Flats as Rungs. Rung spacing is 250mm length and 300mm for 3000mm length of cable Trays. Rungs can be provided Single/Double, as per the Customer’s choice

Race way/Cable Duct

Straight sections of solid bottom cable trays constructed from single sheet of metal, providing excellent protection from external damage. They are used primarily for instrumental control, communication and other non-heat producing cables.

Couplers & Accessories

Application of Coupler Plates: As the standard length of cable trays are 2500mm/3000mm to join every two cable trays coupler plates are used. The thickness of coupler plates will vary 2mm to 3mm depending on customer requirement & design.